3、The machine must be repaired after one year. Including its basic content: Cleaning roller bearing and fill with new lubricating oil. Replace the damaged seal, replace the damaged parts. Purchased components purchased according to the original specifications.
4、設備每運行三年后進行綜合大修，大修基本內容包括：全部拆卸蒸煮機的零部件，清洗舊的安裝部件，除銹，涂防銹漆。檢查容易磨損部件的尺寸，例如：螺旋葉片的厚度，組件間的尺寸，蒸汽管壁的厚度。對所有的零部件及整機進行大修后，蒸汽夾套要進行水壓試驗，試驗壓力應等于工作壓力的1.25倍。
4、The machine must be comprehensive overhaul after three year. Including its basic content: Remove all cooker machine parts, clean the old installation components, derusting, besmear antirust paint. Check the dimensions of the easily worn parts, such as the thickness of the screw blade, the dimensions of the components, the steam pipe wall thickness. After overhaul on all the parts and the whole machine, steam jacket for hydrostatic test, the test pressure shall be equal to the work pressure of 1.25 times.

3、The machine must be repaired after one year. Including its basic content: Cleaning roller bearing and fill with new lubricating oil. Replace the damaged seal, replace the damaged parts. Purchased components purchased according to the original specifications.
煮機是魚粉加工過程中基本的設備，它的主要作用是將原料魚煮熟，使原料魚中的油脂和水份與魚肉纖維分離，以達到下一步壓榨工序的要求。
Cooker is the most fundamental in the process of fish meal processing equipment. Its main role is to cook raw fish. Make the fish oil and water separate with the fiber. So that achieve the next squeezing process requirements.
蒸煮機的工作原理是用蒸汽作加熱介質，原料魚從進料口進入機內，蒸煮機的夾套筒體及帶螺旋夾套葉片的主軸通入蒸汽，吸收熱能。魚料接觸夾套、螺旋葉片被加熱，在螺旋葉片旋轉徐徐移動過程中加熱煮熟，煮熟的魚料在旋轉推動下從出料口排出，通過調節蒸汽的工作壓力和轉速的無級調速，以實現蒸煮機的連續自動的工作狀態。
Cooker working principle is to use steam as a heating medium, Raw fish from the inlet into the machine, Cooker clamp sleeve body and clamp with spiral blade shaft ventilation with steam, absorb heat energy.Fish material is heated by contact jacket, spiral blade. And be cooked thoroughly in the process of the spiral blade rotation slowly moving heat. Cooked fish is discharged from outlet in rotation driven. By adjusting the steam pressure and speed stepless speed regulation, to realize the continuous automatic cooking machine working condition.
2、Technical inspection after each downtime or are in the operation. Check content includes: the sealing device for gas leakage phenomenon. Various control with pressure gauge thermometer is damaged or not. Fasteners loose or tight. Check the steam valve, rotary joints, the hose without leakage, leakage phenomenon.

1、在已建成的基礎上用預埋螺栓將機體固定，在安裝時沿螺旋軸線向冷凝水流出方向傾斜1～3°，進汽端高，出水端低。并且落在基礎上的三個機腳座都必須在同一平面上，以**蒸煮機筒體的主軸的同軸度，在非驅動端的底座固定螺栓與底座要有8㎜的螺栓長孔槽，可以讓筒體在加熱時有軸向的自由度，蒸煮機準確就位固定后，安裝蒸汽，電器部分，要求安全方便操作。
1、Fixed the machine on the basis of the embedded bolt. When installed along the screw axis tilted 1 ~ 3 degree in the direction of condensed water outflow. High end steam in, low end water out. And fell on the basis of three machine feet must be on the same plane, to ensure that the cooking machine cylinder shaft alignment. There must be an 8mm long bolt hole groove between base and the leg in the end without motor. So the cylinder in heating axial of the degrees of freedom. After accurately fixed Cooker, installation steam, electric parts, for safe and convenient operation.
2、調試時要進行點動開機，將蒸煮機主軸轉動幾轉，確認無異常后，啟動電機，由慢到快調節電機至所需轉速，蒸煮機內通入蒸汽后，預熱一段時間，蒸汽的通入也要由低到高漸漸加入，注意觀察各腔的蒸汽壓力和溫度情況是否一致，筒體內有無異響。運行1小時后一切正常調試結束。
2、When debugging need inching switch on. The cooker spindle rotation a few turns, without exception confirmed, then start the motor. From slow to fast to adjust to the desired motor speed. After cooker into steam, preheat a period of time, the flux of steam into the will gradually from low to high. Observe the cavity of the steam pressure and temperature conditions are consistent or not, cylinder body with or without abnormal phenomenon. After one hour normal running, debugging ended.
3、In order to more efficient use of heat source, saving steam dosage, reduce the workshop working environment temperature. The cooker body shell surface equipped with insulation layer. Rock wool or foaming foam insulation materials is available. With a thin aluminum plate or sheet 304 after the completion of the parcel. Fixed with bolts or rivets.

-/gbacfae/-

公司是我國華南地區生產魚粉加工成套設備的廠家，從事魚粉設備研發已有數年歷史，是一家集研發、生產、銷售和服務于一體的機械制造企業，擁有從歐洲引進的**生產工藝以及自主開發的多項創新技術。具備兩個魚粉設備研發加工制造基地，占地面積20畝生產魚粉設備，魚油設備，肉骨粉設備,動物煉油設備，連續水解羽毛粉設備。建有廠房車間13000多平方米，生產廠房規范，設備設施，供電供水系統完備，產品質量檢驗儀器完整。擁有一批高、中級技術職稱科技人員,其中機械工程技術人員25人，有*熟練機械制作員工90多人,公司與北海職業技術學院、中國海洋大學建立了良好的合作關系,并與國內外諸多魚粉加工廠有業務往來，具備產學研合作開發的條件，使產品研發試驗有良好的基礎。產品國內銷售主要是在山東、廣東、廣西、海南等省份，國外銷售主要是在非洲國家如南非、毛里塔尼亞、塞內加爾、幾內亞、摩洛哥、突尼斯，亞洲國家有越南、印度、印度尼西亞、巴基斯坦、泰國、菲律賓、阿曼等，歐美洲國家有秘魯、墨西哥、意大利等。 2014年在的支持下，公司積極響應國家“走出去”和“”方針，在非洲的毛里塔尼亞投資了大型魚粉廠，主要生產和銷售魚粉和魚油。該廠建造在靠近魚資源豐富的大西洋海岸線附近，減少了魚資源的運輸費用，北海新宏恒達機械設備有限公司自主創新開發的國家授權**技術成果對本項產業鏈協同創新發展**項目的實施提供了較強的技術依托基礎，主要**技術成果累計共11項，2010年09月至2012年12月，公司承擔了2010年度國家創新立和廣西科學研究及技術開發計劃（桂科攻1095004）“新型節能封閉式濕法魚粉加工設備”項目。經過兩年的試制研究，成功開發出全封閉式濕法魚粉加工設備，產品生產能力從80噸增加至600噸，滿足了不同客戶的需求。完成了合同約定的各項經濟技術指標，通過了國家科技部創新管理中心和廣西科技廳的項目驗收。