久久机热这里只有精品,久久99久久国产毛片基地,国产精品视频,在线免费观看你懂的,久久久国产精品三区,久久亚洲精品中文字幕,天天添夭天啪天天谢,亚洲精品一区二区91在线,午夜视频完整版在线观看,性爽久久久久男女

    歐萊斯MPB烤漆面金屬油墨
    
    本產品是采用高級進口丙烯酸樹脂和高級顏料經過細制研磨加工組合而成,用于各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面及烤(噴)漆面等制品的絲印及移印,不需加固化劑,不需烘烤,即可獲得優異的附著力。
    油墨特性:
    1、平光、附著力佳、耐汽油、耐化學品;
    2、手感好,流平性佳、面光潔;
    3、表面硬度好,耐沖擊性能強、抗刮傷;
    4、耐汽油、耐酒精、耐化學品程度佳;
    印刷:
    選用網目為100-350目,以120T網紗計算涂覆蓋面積每公斤達30~35㎡。
    表干時間自然揮發5-15分鐘,實干時間在24小時以內,48小時后達較佳性能。
    1.用配套專用稀釋劑開油水
    2.用718洗網水洗網。
    3.或添加配套硬化劑10%可增加附著力,提高墨膜硬度。
    4.烤箱80℃烘烤10分鐘佳能更優。
    測試方法(完全干燥后):
    1.3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。
    
    使用方法:
    1.建議用我公司專用稀釋劑進行稀釋,不建議使用783慢干稀釋劑稀釋,使用前應充分攪拌,用后隨時密封。
    2.攪拌時加本公司配套開油水10-12%,稀釋到印刷適合粘度,移印稀釋使用移印專用稀釋劑;用718洗網水清洗。
    3.不得與其它類型油墨混合使用,否則容易出現其他附著力,化學反應等不良現象。
    4. 加入固化劑的油墨使用時限為8小時,過期請棄用,剩余油墨不可回收
    注意事項:
    1.各種承印物料的外觀相似,但可能會是不同的材料,客戶需先試印,確其符合要求后,再批量生產。
    2.在移印過程中,如出現拉絲或散開,可適當加入一些慢干膏即可;
    3.環境溫度過高,將會影響油墨原有質量。白色追趕150都會變色,烘烤時請用木質材料墊底進行烘烤,不得直接接觸鐵
    4.根據氣候變化,請遠離火源,陰暗處15度-30度環境下存放
    Brand: but MY name: anodic oxidation INK Numbers: 65496 
    Anodic oxidation ink series 
    The product is produced with advanced import acrylic resin and senior pigment after fine grinding system, used in combination to ABS, PP, PET, all kinds of metal, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface and roast (spray paint products of screen and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion. 
    Ink characteristics: 
    1 the classification includs glass, adhesion, good resistance to gasoline, alcohol, resistance to chemicals; 
    2, feel is good, flow ping sex, good surface is bright and clean; 
    3 and fine surface hardness, impact resistance properties of strong, resistance to scratch; 
    4, resistant to gasoline, alcohol, resistant to chemicals resistant degree good; 
    Printing: 
    Choose for 100-350 mesh mesh to 120 T nets yarn with coverage area calculation per kilogram of 30 to 35 ㎡. 
    Dry time table natural volatilize 5 to 15 minutes, action in time within 24 hours, after 48 hours of optimum performance. 
    1. With matching special thinner, open oil and water 
    2. Wash washing nets with 718 net. 
    3. Or add hardener 10% supporting can increase adhesion, improve ink film hardness. 
    4. Preheat the oven to 80 ℃ bake for 10 minutes Canon even better. 
    Test method (dry) : 
    1.3 M tape stuck in the picture has's ink surface 45 degree Angle quickly pull up not to take off oil. 
    2. The purity of 99% alcohol 500 G force in ink surface wipe 300 times back and forth without decoloring. 
    Method of use: 
    1. The proposal with my company special thinner to dilute, not recommended dry thinners diluted 783 slow, before the use should be fully mixing, use at any time after sealing. 
    2. Add the company supporting stirring open 10 to 12%, oil and water dilute the printing for viscosity, pad printing dilution use moving printing special thinner,; Use clean water to wash the nets 718. 
    3. Not with other kinds of printing ink mixed use, otherwise easy to have other adhesion, chemical reactions and other bad phenomenon. 
    4. Add hardener inks use time limit for 8 hours, please not used, the remaining expired ink not recycling 
    Note: 
    1. All kinds of printing material appearance similar, but may be of different material, customers are required to meet the requirements of the ShiYin, indeed, its, then batch production. 
    2. In moving printing process, such as a wire drawing or away, can be appropriately to add some slow dry paste can; 
    3. Environmental temperature is too high, will influence the quality of the original ink. White will change color, roasted beyond 150 when please use woodiness material bottom, and may not directly contact roast iron 
    4. According to climate change, please away from fire, the shadows 15 degrees-30 degrees environment for

    上海歐萊斯印刷油墨科技有限公司是一家以油墨生產,印刷耗材貿易,印刷加工為一體的公司。凱賢科技公司座落在交通便利的嘉定安亭鎮,緊靠F1**賽車場。公司占地面積10000平方米,是一家以研制、生產**油墨為實體,同時經營各類相關輔助器材的科工貿一體化大型企業。以ISO9001質量認證體系為基礎,以歐美EN-71PART3、日本ST-MARK、美國ASTM檢測體系為標準,生產適用于絲印、移印、膠印、噴涂等工藝系列油墨產品,為電子電器、紡織服裝、日用制品、文體用品、包裝印刷、廣告展示、玩具業等國內外眾多行業領域的著名品牌運營商提供優質服務,備受著業界的信賴與推崇。凱賢科技在新時期確立了新的發展戰略,提出了“科研先導,人才運營,整合資源,創新經營”的企業經營方略。與國內外**油墨技術研究機構建立戰略合作伙伴關系,在不斷提高完善現有產品質量的同時,致力于新產品的研制開發。同時完善企業運營機制,積極吸納各類人才,建立*、和諧、熱忱、專注的顧問型服務團隊,運用行之有效的營銷、管理策略,增強了企業與客戶的可持續發展動力與優勢。 作為中國絲網印刷行業協的會單位和中國網印及制像協會的成員,凱賢科技深深感受到自己肩負著推動中國絲網印刷、制像事業走高速健康發展道路的歷史使命。凱賢人決心籍著自身綜合實力,結合


    產品價格:160.00 元/公斤 起
    發貨地址:上海上海包裝說明:不限
    產品數量:100000.00 公斤產品規格:1公斤
    信息編號:44410497公司編號:13613883
    Q Q號碼:445850506
    凱賢(上海)印刷科技有限公司 黃迷女士 銷售經理認證郵箱認證認證 認證 13636471658
    相關產品:PP免處理油墨,PE免處理油墨,自干五金油墨,電鍍表面油墨,尼龍加玻纖油墨
    本頁鏈接:http://www.olmyr.com/wvs44410497.html
    以上信息由企業自行發布,該企業負責信息內容的完整性、真實性、準確性和合法性。免費黃頁網對此不承擔任何責任。 馬上查看收錄情況: 百度 360搜索 搜狗